Allied-telesis AT-S101 Manuale Utente Pagina 65
- Pagina / 238
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
AT-S101 Management Software User’s Guide
65
Mapping CoS Priorities to Egress Queues
This procedure explains how to change the default mappings of CoS
priorities to egress priority queues, as shown in Table 1 on page 63. This
is set at the switch level. You cannot set these mappings on a per-port
level. You can also use this procedure to enable and disable QoS on the
switch.
To change the default mappings of CoS priorities to egress priority queues
or to enable or disable the QoS feature, perform the following procedure:
1. From the menu on the left side of the page, select Bridge.
The Bridge folder expands to show the VLAN folder.
2. From the VLAN folder, select CoS.
The CoS Page is shown in Figure 21.
Figure 21. CoS Page
3. To enable or disable QoS, select Enable or Disable from the QoS
Status pull-down menu. The default is Disable.
4. To change the egress priority queue assignment of an 802.1p priority
class, click the dialog circle of the queue for the corresponding priority.
- User’s Guide 1
- Contents 3
- Document Conventions 10
- Contacting Allied Telesis 12
- Chapter 1 13
- Switch’s IP Address 14
- Save Configuration 17
- Web Browser Tools 18
- Basic Switch Parameters 21
- Setting Up the IP Access List 24
- Deleting an IP 26
- Adding System 31
- Administration 31
- Information 31
- Modifying 32
- Deleting 33
- Viewing System Information 36
- Rebooting a Switch 39
- Pinging a Remote System 41
- Average Time 43
- Virtual LANs 45
- VLAN Overview 46
- Tagged VLAN 48
- Tagged and Untagged Ports 49
- Port VLAN Identifier 49
- Chapter 3: Virtual LANs 50
- Creating a Tagged VLAN 51
- Modifying a Tagged VLAN 53
- Deleting a Tagged VLAN 55
- Creating a Port-Based VLAN 56
- Modifying a Port-Based VLAN 57
- Deleting a Port-Based VLAN 59
- Quality of Service (QoS) 61
- Configuring CoS 67
- Port Configuration 71
- Chapter 5: Port Configuration 74
- Port Trunking 77
- Port Trunking Overview 78
- Static Port Trunk Guidelines 79
- Creating a Port Trunk 80
- Modifying a Port Trunk 82
- 7. Click Apply 83
- Disabling a Port Trunk 84
- LACP Port Trunks 85
- LACP Overview 86
- Chapter 7: LACP Port Trunks 88
- LACP System Priority 90
- Key Parameter 90
- LACP Port Priority Value 90
- Displaying LACP Group Status 94
- Selecting Port Priority 96
- Chapter 8 99
- SNMP Overview 100
- Community String Attributes 101
- Creating an SNMP Community 104
- Modifying an SNMP Community 105
- Deleting an SNMP Community 106
- Creating a Host Table 107
- Modifying a Host Table Entry 108
- Deleting a Host Table Entry 109
- Enabling or Disabling Traps 110
- Modifying Traps 111
- Deleting Traps 112
- IGMP Snooping 113
- Overview 114
- Configuring IGMP Snooping 116
- Chapter 9: IGMP Snooping 118
- Bandwidth Control 119
- Setting Bandwidth Control 121
- Chapter 10: Bandwidth Control 122
- Port Mirroring 123
- Configuring Port Mirroring 125
- Disabling Port Mirroring 126
- Static Multicast MAC Address 127
- Protocols 133
- Path Costs and 136
- Port Costs 136
- Hello Time and 138
- Bridge Protocol 138
- Data Units 138
- Point-to-Point Ports 139
- (Full-duplex Mode) 139
- Edge Port 140
- Point-to-Point and Edge Port 141
- Workstation 141
- Mixed STP and RSTP Networks 142
- Spanning Tree and VLANs 143
- Configuring the 148
- Basic RSTP Port 148
- Settings 148
- Advanced RSTP 150
- Port Settings 150
- Chapter 14 157
- Authentication 159
- Authenticator 159
- AT-GS950/8POE 160
- Port-based 161
- Network Access 161
- Guidelines 161
- Switch A 163
- Switch B 163
- Guest VLANs 164
- Chapter 15 169
- Configuring the RADIUS Client 171
- Destination MAC Filter 173
- Power over Ethernet (PoE) 179
- Port Power Priority 181
- Setting Power over Ethernet 182
- Classifiers 185
- Classifier Criteria 187
- VLAN ID 188
- Protocol (Layer 2) 188
- DSCP (DiffServ Code Point) 189
- Protocol 189
- Creating Classifiers 192
- Chapter 18: Classifiers 194
- Access Control Policies 195
- ACP Components 197
- Creating Profile Action 199
- Creating an In-profile Action 201
- Creating a Policy 206
- Displaying a Policy Sequence 208
- Management Software Updates 209
- Statistics 219
- Chapter 21: Statistics 222
Prodotti e manuali riguardandi Hardware del computer Allied-telesis AT-S101
(48 pagine)© 2020, manymanuals.it. Tutti i diritti riservati | 0.127 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale