Allied Telesis x900-48FS Guida di Installazione

Installation GuideRemovable Power Supply and FanAT-PWR01AT-PWR02AT-PWR05AT-FAN01AT-FAN03

Installation Guide9Connecting an AC power supplyFollow these instructions to connect an AT-PWR01, AT-PWR02, or AT-PWR05 AC PSU to an AC power supply:W

Removable Power Supply and Fan10Connecting a PWR01 or PWR021. Plug the supplied AC power cable into the power inlet on the PSU and attach the retainin

Installation Guide112. Plug the AC power cable into the power inlet on the PSU.3. Connect the power cable to the main power source.4. Check that the R

Removable Power Supply and Fan12Connecting a PWR01 DC power supplyFollow these instructions to connect an AT-PWR01 DC PSU to a DC power supply. Only t

Installation Guide13• All grounding points are at the same ground level. That is, all power connectors share a common power distribution unit. Warnin

Removable Power Supply and Fan14Connecting a PWR05 DC power supplyFollow these instructions to connect an AT-PWR05 DC PSU to a DC power supply. Only t

Installation Guide151. Ensure that the circuit breaker for the supply circuit and the Run/Standby switch on the PSU are off (slide to position O). 2.

Removable Power Supply and Fan16Checking LEDsLEDs on PSUs, fans, and the front panels of switches indicate the operational status of the devices. Afte

Installation Guide17PWR05 ACThe following table describes LEDs on the PWR05 AC power supply unit.PWR05 DCThe following table describes LEDs on the PWR

Removable Power Supply and Fan18FAN03 The following table describes LEDs on the FAN03 chassis fan module. Switch The following table describes how LED

Removable Power Supply and Fan Installation GuideAT-PWR01 AT-PWR02 AT-PWR05 AT-FAN01 AT-FAN03Download the complete document set from www.alliedtelesi

Installation Guide19Removing a Power Supply Unit or FanFollow these instructions to remove a PSU, chassis fan module, FOM or blanking plate.Before you

Removable Power Supply and Fan20The following is a diagram of PWR05 and FAN03 3. Remove the PSU, chassis fan module, FOM or the blanking plate from t

Installation Guide21Avoid the spinning blades on FAN03. Contact may cause personal injury or damage the unit. Do not operate the switch for extended p

Removable Power Supply and Fan22TroubleshootingIf the PSU does not function as expected: Check that all cable connections are correct and secure. On

Installation Guide23Obtaining Documentation and ResourcesThe complete document set for x900 Series switches and SwitchBlade x908 includes: this Insta

Removable Power Supply and Fan24AT-TFTP Server for Windows is a TFTP (Trivial File Transfer Protocol) server for transferring software versions, confi

Installation Guide25StandardsWhere applicable, the products in this document meet the following standards:Category Approval Agency and Requirement S

Removable Power Supply and Fan2Removable Power Supply and Fan Installation Guide Document Number C613-04057-00 REV S© 2012 Allied Telesis, Inc. All ri

Installation Guide3ContentsAbout this Guide ...

Removable Power Supply and Fan4About this GuideThis Installation Guide describes how to install the following PSUs and fans: AT-PWR01 PSU, either AC

Installation Guide5Package ContentsDepending on the model, switches are shipped with a single supply unit (PSU), either AC or DC. Some models also hav

Removable Power Supply and Fan6Installing a Power Supply Unit or FanUse these instructions to install PSUs, chassis fan modules and FOMs. Do not comb

Installation Guide7Installing a PWR01, PWR02, or FAN011. If there is a PSU, fan or blanking plate in the bay you wish to install the unit, first remov

Removable Power Supply and Fan8Installing a PWR05 or FAN031. If there is a PSU, fan or blanking plate in the bay you wish to install the unit, first r