Allied-telesis AT-MC13 Manuale Utente

AT-MC13Ethernet Media ConverterInstallation GuidePN 613-000660 Rev A

Preface10Document ConventionsThis document uses the following conventions:NoteNotes provide additional information.CautionCautions inform you that per

AT-MC13 Media Converter Installation Guide11Where to Find Web-based GuidesThe installation and user guides for all Allied Telesis products are availab

Preface12Contacting Allied TelesisThis section provides Allied Telesis contact information for technical support as well as sales or corporate informa

13Chapter 1OverviewThe AT-MC13 Ethernet Media Converter is designed to extend the distance of your network by interconnecting twisted pair cabling to

Chapter 1: Overview14Key FeaturesThe AT-MC13 media converter has the following key features: LEDs for unit and port status Full- or half-duplex mode

AT-MC13 Media Converter Installation Guide15Twisted Pair PortThe AT-MC13 media converter has one 10Base-T twisted pair port. The twisted pair port fea

Chapter 1: Overview16depending on its capabilities. An end-node that is operating in half-duplex mode can either send data or receive data, but it can

AT-MC13 Media Converter Installation Guide17MDI/MDI-X SwitchAn RJ-45 port on a 10 Mbps Ethernet network device can have one of two possible wiring con

Chapter 1: Overview18NORMAL/LNK TST ButtonThe AT-MC13 media converter features a NORMAL/LNK TST (Normal MissingLink/Link Test) button, shown in Figure

AT-MC13 Media Converter Installation Guide19The value to this type of network monitoring and fault notification is that some hubs and switches can be

Copyright © 2006 Allied Telesis, Inc.www.alliedtelesis.comAll rights reserved. No part of this publication may be reproduced without prior written per

Chapter 1: Overview20External Power AdapterAn external AC/DC power adapter, shown in Figure 6, is provided with the media converter for use on a deskt

AT-MC13 Media Converter Installation Guide21Network TopologiesThe AT-MC13 media converter can be used in two different topologies: Standalone and Back

Chapter 1: Overview22Back-to-Back TopologyIn some network configurations you may want to interconnect two media converters in what is referred to as a

23Chapter 2InstallationThis chapter explains how to install the AT-MC13 media converter. This media converter can be used on a desktop or installed in

Chapter 2: Installation24Planning the InstallationBe sure to observe the following guidelines when planning the installation of your media converter.

AT-MC13 Media Converter Installation Guide25Reviewing Safety PrecautionsPlease review the following safety precautions before you begin to install the

Chapter 2: Installation26Pluggable Equipment: The socket outlet should be installed near the equipment and should be easily accessible.  E5CautionAir

AT-MC13 Media Converter Installation Guide27Installing an AT-MC13 Media ConverterThe AT-MC13 media converter can be used on a desktop. To use an AT-MC

Chapter 2: Installation28Cabling an AT-MC13 Media Converter1. Remove the dust cover from the fiber optic port and connect the fiber optic cable to the

AT-MC13 Media Converter Installation Guide293. Set the MDI/MDI-X switch as follows: If you are connecting a workstation to the twisted pair port, set

3Electrical Safety and Emission Compliance StatementStandards: This product meets the following standards.U.S. Federal Communications CommissionDeclar

Chapter 2: Installation30Powering on an AT-MC13 Media ConverterTo apply power to an AT-MC13 media converter, perform the following steps:1. Plug the A

AT-MC13 Media Converter Installation Guide31Warranty RegistrationWhen you finish installing the product, you should register your product by completin

33Chapter 3TroubleshootingFollow the guidelines below to test and troubleshoot the installation in the event a problem occurs.If the PWR LED is OFF, d

Chapter 3: Troubleshooting34If the LINK LED for the fiber optic port is OFF, do the following: Verify that the end-node connected to the port is ON a

AT-MC13 Media Converter Installation Guide35If the NORMAL LED on the AT-MC13 is OFF, do the following: Check that the end-nodes connected to the medi

37Appendix ATechnical SpecificationsPhysicalDimensions: W x D x H10.5 cm x 9.5 cm x 2.5 cm(4.125 in x 3.75 in x 1.0 in)Weight: .295 kg (.65 lbs)Temper

Appendix A: Technical Specifications38Agency CertificationsEMI FCC Part 15 Class B, EN55022 Class B, VCCI Class B, C-TICKImmunity EN55024Electrical Sa

AT-MC13 Media Converter Installation Guide39Table 4 lists the cabling specifications for the fiber optic port when operating in full-duplex mode.Table

Electrical Safety and Emission Compliance Statement4EMI FCC Part 15 Class B, EN55022 Class B, VCCI Class B, C-TICKImmunity EN55024Electrical Safety UL

Appendix A: Technical Specifications40RJ-45 Twisted Pair Port PinoutsFigure 11 shows the pin layout to an RJ-45 connector and port.Figure 11. RJ-45 Co

AT-MC13 Media Converter Installation Guide41AT-MCR1 ChassisThe AT-MCR1, shown in Figure 13, is a chassis with internal power designed to house one uni

43Appendix BCleaning Fiber Optic ConnectorsThis section describes how to clean fiber optic connections. The fiber optic connector consists of a fiber

Appendix B: Cleaning Fiber Optic Connectors44This appendix provides the following procedures: “Using a Cartridge-Type Cleaner” on page 44 “Using a S

AT-MC13 Media Converter Installation Guide452. Place the ferrule tip on the exposed cleaning surface and rub the ferrule in a downward direction, as s

Appendix B: Cleaning Fiber Optic Connectors46NoteDo not touch the end face of the ferrule in the connector.WarningDo not stare into the laser beam. 2

AT-MC13 Media Converter Installation Guide47To clean a recessed ferrule using a swab, perform the following procedure.1. Insert the swab into the adap

AT-MC13 Media Converter Installation Guide5Translated Safety StatementsImportant: The  indicates that a translation of the safety statement is availa

7ContentsElectrical Safety and Emission Compliance Statement ... 3Translated Safety Statements...

Contents8Chapter 2Installation ....... 23Verifying P

9PrefaceThis guide contains instructions on how to install an AT-MC13 Ethernet Media Converter. How This Guide is OrganizedThis guide contains the fol